







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Bathroom Remodeling: The Paradise Owner’s Guide
We install CGI-compatible bathroom remodeling in Paradise, and most full bathroom projects run $9,000 – $28,000 installed. Smaller baths land in the $5,000 – $12,000 range, and a walk-in shower alone runs $4,500 – $12,000. We’re an independent service provider and not affiliated with CGI – we work with their products and the compatible parts that fit them.
Owners in Paradise usually find out something’s wrong the same way: they plan a refresh around existing CGI fixtures, then discover the valve cartridge is dripping, the shower pan is flexing underfoot, or the glass door no longer shuts square. In our drier high-desert climate, we see hard-water scale and seasonal temperature swings chew through cartridges and door seals faster than owners expect. Once one piece of the assembly fails, the whole remodel conversation changes. It’s not about cosmetics anymore – it’s about matching parts and doing the install so it holds.
Which CGI Models This Applies To

CGI products show up across a wide spread of series lines, so the model matters before anyone orders a part. The fastest way to identify yours is the label on the inside of the vanity door, under the sink bowl, or on the frame of a shower enclosure. That sticker lists the series and model number, and it’s the number that decides whether a replacement cartridge, hinge set, or shower base is the right size.
Common gotchas we run into:
- Series revisions. CGI has quietly revised cartridge and hinge designs over the years. Two vanities that look identical can take different internals, and the year on the label is the tell.
- Measure twice on shower bases. A 60-inch base is nominal. Actual footprint and drain offset vary by series, and a quarter-inch off means the pan won’t seat without a wet-set adjustment.
- Glass and door hardware. Pivot and hinge hardware is series-specific. The bracket that fits one line won’t fit another, even if the door size matches.
On OEM versus aftermarket: for moving parts like cartridges and hinges, we lean OEM because the tolerances match the housing. For trim and non-load-bearing pieces, a quality aftermarket equivalent is often a smarter spend. Our technicians have up to 21 years of experience, so we can look at your label and tell you which side of that line your part sits on.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Bathroom Remodeling Is Failing
Here’s what homeowners in Paradise describe to us when they call. Each symptom points to a specific cause, and catching it early usually means a smaller job.
- The faucet runs a thin stream or drips when shut off. That’s a cartridge with mineral buildup or a worn seal. In Paradise’s hard water, scale inside the cartridge is the most common culprit we see.
- The shower pan flexes underfoot or cracks at the drain. A subfloor or pan that wasn’t properly supported from install. Flexing lets water past the waterproofing and softens the floor beneath.
- The glass shower door won’t close square or the hinge sags. Worn pivot hardware or a settled frame. Left alone, the sagging door stresses the hinge point and eventually catches on the base.
- Caulk and grout lines keep failing at the floor and corners. Seasonal temperature swings in our climate move joints more than owners expect, and builder-grade sealant gives out early. Recurring failure usually means the joint needs a flexible seal, not another bead of the same caulk.
- The vanity sags, or drawers and doors bind. A cabinet that wasn’t anchored to the wall stud properly, common in bathrooms tiled before the vanity went in.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed pricing for CGI-compatible bathroom work in Paradise:
| Project | Installed Range |
|---|---|
| Full bathroom remodel | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Shower replacement | $3,000 – $8,500 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Vanity installation | $800 – $3,000 |
What drives you toward the top of the range: waterproofing method, tile choice, moving the drain or plumbing, and whether the subfloor needs repair. We give you a written price before work starts, itemized parts and labor, so the number on the invoice is the number you approved. Every job is covered by our 365-Day Done Right Promise, and we pull the permits and pass the inspections.
DIY or Call Us?
Some of this is safe to look at yourself. Re-caulk a failing joint, check that the vanity is screwed into studs, tighten a loose doorknob-style hinge screw. Cleaning mineral scale off a showerhead is fine too.
But anything that touches plumbing or holds back water is where DIY goes wrong. Pulling a cartridge can break the valve body if the retainer clip won’t release. Tearing out a shower pan to re-seat it means redoing waterproofing, and if that fails you’re looking at mold and a floor repair. Moisture behind tile doesn’t announce itself. If you’re not sure a leak is getting through, that’s the moment to stop and get eyes on it. A failed repair under our watch gets a free second visit, no argument, and that accountability is the reason to call rather than experiment. Call (866) 977-0526 to schedule your free estimate in Paradise.
FAQs

Expect 10 – 15 years from a cartridge or valve and 15 – 20 from a properly installed vanity or shower base. Our hard water and big temperature swings push wear faster than a humid climate would, so scale buildup and joint movement are the usual failure points.
Sometimes. A dripping valve is often just a cartridge and seal, which is a modest repair rather than a full replacement. Cracked pans or failed waterproofing aren’t repairable, so we’ll tell you which you’re looking at before quoting. Call (866) 977-0526 for an honest assessment.
A cartridge or hinge swap is usually a couple of hours. A vanity replacement runs about half a day, and a full shower replacement takes one to three days depending on waterproofing. We track a live arrival time so you’re not stuck waiting on a four-hour window.
We identify your model from the label, then order the OEM cartridge or hinge from the manufacturer or an authorized distributor. We don’t keep parts on a truck or in stock. We also install KraftMaid, Cambria, and Silestone components if you’re remodeling around the failing piece. Call (866) 977-0526 for a free estimate.
Written by the team at Sawyer Remodeling Paradise, serving Paradise and nearby areas.












