







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Windows & Doors: The Paradise Owner’s Guide
We install and replace CGI-compatible windows and doors for Paradise homeowners, and installed pricing typically lands between $4,500 and $15,000 for window replacement or $8,000 and $25,000 for impact-rated units, depending on count and glazing. If a unit is still available from the manufacturer, most replacements can be completed in a single day. Most Paradise owners don’t discover the problem until a door drags on the frame in July, a window fogs between the panes after a monsoon, or the latch stops catching and the door won’t hold closed against wind. That’s when the questions start: which series do I have, what part actually failed, and can it be swapped before the next heat wave.
Key Takeaways
- CGI windows and doors in Paradise generally run $4,500 to $15,000 installed for standard replacement and $8,000 to $25,000 for impact units.
- Most “failed” units are glazing or hardware failures, not frame failures, and can often be repaired without a full swap.
- Paradise’s summer heat cycling and monsoon wind loads accelerate seal and hardware wear faster than inland climates.
- We’re an independent service provider, not affiliated with CGI, and we source compatible parts to match your series.
- Written price before any work starts, and a written guarantee on every repair.
Which CGI Models This Applies To

CGI builds residential aluminum, vinyl, and impact-rated window and door lines across several series, and the part you need depends entirely on which series is sitting in your wall. The series label is usually a small etched or stickered plate on the upper jamb of a window sash or the hinge side of a door frame. If the label is gone, we identify the unit by measuring glass unit thickness, sightline depth, and sash profile, and by checking whether the frame is thermally broken aluminum (common in older Paradise builds) or vinyl. CGI impact units use laminated glass with a different glazing bead and sealant than standard units, so a bead from a non-impact line won’t seat correctly even if it looks close.
On the OEM-versus-aftermarket call: for glass units and seals, we recommend OEM or a manufacturer-matched equivalent because the glass make-up (thickness, laminate, spacer) has to match the frame channel exactly. For hardware like rollers, latches, locks, and screens, quality aftermarket parts from established suppliers perform as well as OEM at a lower price, and we’ll tell you plainly when the aftermarket is the smarter spend. We don’t carry a stock of parts and we don’t have parts on a truck; we source to your model, which means we measure and identify first, then order.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Windows and Doors Is Failing
Paradise gets real heat, real wind, and real dust, and CGI units show their age through specific symptoms. Here’s what we look for on a first visit.
- Fogging or condensation between panes. The insulated glass seal has failed, letting moisture into the air space. In Paradise’s heat cycle, this usually shows up 8 to 12 years into a unit’s life, faster on west-facing glass.
- Door drags or rubs the frame. Worn rollers or a shifted hinge, or the frame has moved from soil expansion after monsoon season. If the door binds only in summer, thermal expansion of the frame is the likely culprit.
- Latch or lock won’t engage. The strike plate has shifted or the lock mechanism has worn. On a Paradise door facing wind exposure, this is a security issue, not just an annoyance, and we treat it as one.
- Draft or dust intrusion along the sash. Weatherstripping or the glazing bead has degraded. Dust blowing in along the perimeter is a classic Paradise sign that the seal is gone.
- Water staining on the interior sill. The unit’s weep system or perimeter sealant has failed, and monsoon rain is getting past the frame. Left alone, this leads to drywall and framing damage.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost and What’s Included

Installed window replacement in Paradise runs $4,500 to $15,000 for a typical whole-home set, and impact-rated window installation runs $8,000 to $25,000. A single-unit swap or glass-only replacement sits at the low end; full-frame replacement with new flashing and trim sits at the high end. What drives the range: unit count, glazing type (standard versus impact laminated), frame material, whether the opening needs reflashing, and whether the interior trim has to be rebuilt.
Every quote we give is a written line-item price before any work starts, with parts and labor separated so you can see exactly where the money goes. No surprise number on the invoice. Every repair carries a written guarantee, and if the repair fails, we come back at no charge. The 365-Day Done Right Promise covers the whole job for a full year after close.
DIY or Call Us?
Here’s the honest split. You can safely check for fogging between panes, vacuum or brush the door track, tighten visible hinge screws, and inspect the weatherstripping with a flashlight from inside. Those checks cost nothing and tell you a lot. What we don’t recommend trying yourself: replacing an insulated glass unit (the unit is heavy, the glazing bead has to reseat perfectly or the seal fails again), adjusting a frame that’s shifted (you can crack the glass or break the seal), or reflashing a leaking window opening, which is the top cause of water damage we see after monsoon season. If you find fogging, a dragging door, or water staining, it’s worth a call before it turns into framing repair. Call (866) 977-0526 and we’ll tell you straight whether it’s a repair or a replace.
FAQs

Standard CGI units typically hold their seal for 15 to 20 years, and impact units generally last longer because the laminated glass and heavier frame resist heat cycling better. In Paradise, expect the seal and hardware to wear toward the shorter end on west- and south-facing glass, since those faces take the most UV and thermal swing. Call (866) 977-0526 if you’re not sure how old your unit is.
Yes, in most cases. A fogged unit usually just needs a new insulated glass unit, and a dragging or mis-latched door usually needs new rollers, a lock, or hinge adjustment. Full-frame replacement is only needed when the frame itself is damaged or the wall opening has failed. We’ll tell you which it is before you commit.
A single glass unit or hardware repair is typically a half-day job. A full window or door replacement usually runs one to two days depending on count and whether trim has to be rebuilt. We give you a live arrival time and before-and-after photos on every job, so you know exactly when we’ll be there and what got done.
We identify your series from the label or by measurement, then order the OEM or manufacturer-matched part to fit. We don’t keep parts in stock and we don’t carry them on a truck, so lead time depends on the part. Quality aftermarket hardware is often available faster and at a lower price, and we’ll say so when that’s the better call.
If your CGI window or door in Paradise is fogged, dragging, or leaking, the fastest way to get a straight answer and a written price is to call us. Call (866) 977-0526 for a free estimate. We also service KraftMaid, Cambria, and Silestone products across Paradise and nearby areas.
Written by the team at Sawyer Remodeling Paradise, serving Paradise and nearby areas.












