







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Paradise Owner’s Guide
We install Schluter-based home additions and ADUs throughout Paradise, and most projects land between $45,000 and $130,000 depending on square footage, slab work, and how much wet-area waterproofing the build needs. If you’re pricing a detached or attached ADU, that separate category runs $90,000 to $220,000. The calls we get aren’t usually about a part that snapped off a truck – they come from owners whose addition has moisture creeping into a slab edge, mold climbing a shower wall inside a new guest suite, or grout going dark at a bathroom threshold that was finished with a Kerdi-Line drain and never pitched right.
Key Takeaways
- Schluter systems fail at the waterproofing layer, not the tile. That’s the part worth understanding before you price a repair.
- Sawyer Remodeling Paradise is an independent service provider, not affiliated with Schluter.
- Written price before any work starts. 365-Day Done Right Promise on every job.
- Our technicians have up to 21 years of experience with wet-area builds and ADU framing.
Which Schluter Models This Applies To

Schluter doesn’t sell one product called “addition.” The name covers a family of systems you’ll find in an ADU or addition build, and knowing which one is under your tile is the whole game. The lines that matter most in Paradise are Kerdi (sheet-applied waterproofing membrane behind tile), Kerdi-Board (foam backer panels for showers and wet walls), Ditra and Ditra-Heat (uncoupling membrane under floor tile), and Schluter-Kerdi-Line linear drains. The trim line every owner trips over is Schluter-Reno-U, the edge profile that bridges tile to carpet, laminate, or slab.
Here’s the compatibility gotcha that burns people: Ditra and Ditra-XL have different ten-year thickness specs (roughly 1/8-inch and 5/16-inch), and the thinset selection changes with it – modified vs. unmodified matters. If someone swapped XL in where standard Ditra was specced under a heated floor, the tile can telegraph movement joints. Look for the orange printed webbing and the model stamp on the edge, not the box, because boxes get thrown away.
On OEM vs. aftermarket: Schluter holds its own patents and the genuine membrane is what carries the waterproofing warranty backing. There are generic uncoupling mats that work fine for thermal movement, but they don’t match Schluter’s system warranty, and mixing brands inside one shower assembly voids the whole assembly. For anything feeding a drain or a wet wall, we specify genuine Schluter and write it into the estimate.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
- Grout lines darken or turn gritty at the shower floor. That’s usually water sitting under the tile because the membrane was installed without the correct overlap or a proper pre-sloped pan, so moisture has nowhere to go but up.
- Hollow thud when you tap new floor tile. Uncoupled tile or a thin thinset layer over Ditra will sound hollow across a patch; that patch is where a tile will pop.
- Loose edge trim where the bathroom tile meets the hallway floor. Reno-U profiles come in different reveal heights, and a 10mm profile over a 3/8-inch tile leaves a lip that catches a bare foot and lifts.
- Musty smell in the closet or the inside of the exterior wall shared with the bath. That’s membrane termination above the curb or a missed vertical overlap pulling moisture into the framing, and in Paradise’s dry heat you’ll smell it before you see it.
- Linear drain pooling despite a “level” floor. Kerdi-Line installs are unforgiving on pitch: a drain set too high or a pan that’s flat by a fraction leaves standing water that eventually wicks at the edges.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Most of what we price in Paradise under the Schluter umbrella isn’t a single part swap – it’s a wet-area or floor section rebuild, and that’s why it falls under the home addition range of $45,000 to $130,000 on a broader project or a smaller repair inside that work. Actual line items depend on how much tile gets torn out, whether framing is wet, and whether the drain or valve has to be reset. Every job carries a written line-item quote before any tool comes out of a van, a live arrival window, and photo updates before and after so you see the membrane and the pre-slope, not just the finished tile. Labor and material are both spelled out, and the 365-Day Done Right Promise backs the work for a full year after the project closes.
DIY or Call Us?
You can safely check some of this yourself. Look at the model stamp on the Ditra or Kerdi edge, measure your tile thickness and the reveal on your Reno-U profile, note whether the shower drain is linear or center, and photograph any damp or hollow-sounding spots. What we don’t recommend is tearing into a wet-area assembly or a heated floor to “take a look” – the waterproofing layer is a continuous system and once you cut it, the whole assembly has to be rebuilt to the same spec, and getting the overlap and thinset wrong creates a moisture path that shows up six months later as rot in the framing behind the wall. For anything behind tile or feeding a drain, get a trained eye. Call us at (866) 977-0526 and we’ll talk you through what we see in Paradise homes like yours.
FAQs

Properly installed, a Kerdi membrane or Ditra assembly should hold up for the life of the tile job – 20-plus years is realistic when the pre-slope and overlaps are done right. In Paradise, the front-side problem isn’t moisture coming in, it’s moisture getting trapped inside because a homeowner kept a shower sealed and shut between uses in 105-degree summers. Airflow matters as much as the membrane. Call (866) 977-0526 for an on-site look at your assembly.
Sometimes yes, but rarely at the waterproofing layer – a loose edge trim or a single popped tile can often be repaired in place if the membrane underneath is intact. A leaking pan or a compromised drain cannot be patched, because the fix is under the tile. We tell you honestly which one you’re looking at before quoting. Call (866) 977-0526 for that assessment.
A trim or single-tile fix is usually a half-day. A shower pan rebuild runs three to five days once demo and set times are counted, and an addition-scale wet-area section is part of the larger project schedule. We give you a written timeline with the price. Call (866) 977-0526 to get it scheduled.
We specify genuine Schluter components from established distributors matched to the exact model and thickness your assembly calls for, not a generic substitute that would void the system warranty. We don’t stock parts on a truck – every part is ordered to your job. Alongside Schluter, we work with KraftMaid, Cambria, and Silestone finishes so the whole room reads as one plan. Call (866) 977-0526 for a free estimate.
Written by the team at Sawyer Remodeling Paradise, serving Paradise and nearby areas.












